The running in of diesel generator set is a necessary measure to prolong its service life. There are geometric errors (positional accuracy errors) and micro unevenness (bumps and dents formed by machining marks) in diesel engine assembly and main friction pair parts, such as cylinder and piston, piston ring, crankshaft journal and bearing, etc. Therefore, the actual contact area of the two parts is small, but the load per unit area is large, so the friction and wear are serious. In addition, the oil film is not easy to be damaged due to the uneven surface. If the diesel engine works at high speed and high load, the bumps on the surface of the friction pair parts will be seriously scratched or torn, and the metal chips will become abrasives, which will aggravate the wear. In severe cases, local high temperature melting changes into dissolution wear, forming cylinder burning. In fact, due to the rough surface of the parts, the power consumed in friction is large, so the high load of diesel engine is equivalent to overload. As a result, it also aggravates the wear of parts.

柴油發電機組磨合期較長，而初期磨合階段磨損量較大，因此，此階段一般以工廠內進行，通過合理的磨合規范進行磨合，以減少磨損量，延長使用壽命，同時通過磨合期可以用來檢查和調整柴油機的裝配質量和性能參數，以及運行中出現的問題，以便及時排除，使柴油機質量和性能達到規范的要求。

The running in period of diesel generator set is long, while the wear loss in the initial running in stage is large. Therefore, this stage is generally carried out in the factory, and the running in is carried out through reasonable running in specifications, so as to reduce the wear and prolong the service life. At the same time, the running in period can be used to check and adjust the assembly quality and performance parameters of diesel engine, as well as the problems in operation, so as to eliminate them in time, The quality and performance of diesel engine can meet the requirements of specification.

新的或經大修后的柴油發電機組，在正式使用前須經60h磨合運轉，方可投入全負荷使用，以改善柴油機各運動部件的工作狀況，提高柴油機的運行可靠性和使用壽命。磨合應視柴油機用途和拖載方式的不同，來考慮具體磨合方案。原則上隨著磨合時間的增加，分階段逐步提高柴油機的轉速和負載，在整個磨合期內負荷以12h標定功率的50%~80%為宜，轉速應不大于標定轉速的80%為好。但在磨合的開始階段，空運轉或過小負載情況下的運轉時間不宜過長。每當修理更換過缸套、活塞、活塞環、連桿軸瓦和曲拐等零部件后，亦應按上述磨合工況適當進行短期磨合。

The new or overhauled diesel generator set can be put into full load operation only after running in for 60 hours before formal use, so as to improve the working conditions of all moving parts of diesel engine and improve the operation reliability and service life of diesel engine. The specific running in scheme should be considered according to the different use of diesel engine and different towing mode. In principle, with the increase of running in time, the speed and load of diesel engine should be gradually increased in stages. During the whole running in period, the load should be 50% ~ 80% of the rated power of 12h, and the speed should not be greater than 80% of the rated speed. However, the running in period should not be too long under the condition of small load. Whenever the cylinder liner, piston, piston ring, connecting rod bearing bush, crank and other parts are repaired and replaced, the short-term running in should be carried out according to the above running in conditions.

有了沼氣發電機組上面的小總結，希望對廣大客戶有所幫助，如果有什么不理解的或者尋求幫助的請點擊我們的網站：http://m.hdlelisa.com 或者來電咨詢，我們會盡全力為您解決

With the summary of biogas generator set, we hope to help our customers. If there is anything you don't understand or ask for help, please click our website: http://m.hdlelisa.com  Or call consultation, we will try our best to solve it for you